MOPAR PERFORMANCE MANUAL TRANSMISSION PARTS

HURST PISTOL GRIP SHIFTERS

Exclusively through Mopar Performance, Hurst Pistol Grip Shifters are back! Give your 4-speed Mopar muscle car that original look and feel it deserves with these brand-new factory reissued pistol grip shifters from Hurst.
(Please note: If you have the push in type handle that is not held in by two bolts, you can still use these handles by simply drilling two holes through you're existing mechanism).

Hurst Pistol Grip Shifter (All 1968-69 Non-Console, 1970 B-Body Non-Console)

$ 649.95

Hurst Pistol Grip Shifter (1971-74 B-Body Non-Console with Center Armrest)

$ 649.95

Hurst Pistol Grip Shifter (1970-74 E-Body, 1971-74 B-Body with Console)

$ 649.95

Hurst Pistol Grip Shifter (1970 B-Body with Console)

$ 999.95

HURST PISTOL GRIP WOODGRAIN GRIPS

Hurst Pistol Grip Simulated Wood Grain Insert

$ 29.95

CAST CRANK FLYWHEEL

Replacement Flywheel for the 360 cast crank engine with external balance. Not SFI approved. It is 6-bolt for 10 1/2" clutch.

Cast Crank Flywheel -- 130 Tooth (1971-92 360 Small Block, not AMC, 5.9L Magnum/Jeep® Engines)

$ 359.95

RACE STEEL FLYWHEEL

This Race Steel V8 Flywheel weighs 18 1/2 lbs. and is designed for use with 10 1/2" clutch.

Race Steel Flywheel — 6-Bolt (Big Block, Small Block)

$ 319.95

STEEL REPLACEMENT FLYWHEELS

Steel Replacement Flywheels weigh 30 lbs. and are for use with 10 1/2" clutch. Not SFI approved.

Steel Flywheel — 6-Bolt, 130 Tooth (Big Block, Small Block)

$ 399.95

Steel Flywheel — 8-Bolt, 130 Tooth (Big Block, Small Block)

$ 399.95

FLYWHEEL ATTACHING SCREW SET

This Flywheel Attaching Screw Set is ideal for inline 6 and 90° V6 and V8 engines. It includes 6 crankshaft and pressure plate bolts.

Flywheel Attaching Screw Set — 6-Bolt (V8 and 6-cyl.)

$ 4932.95

CLUTCH FORK REPLACEMENT KITS

Replacement Kits for rear-wheel-drive manual transmission clutch forks. Kits contain a clutch fork, clutch fork pivot and boot.

Clutch Fork Repair Kit — 12 1/2" Approx. Length (Small Block A-Body, Except 1976)

$ 199.95

Clutch Fork Repair Kit — 10" Approx. Length (Small Block B- and E-Body)

$ 259.95

Clutch Fork Repair Kit — 10 3/4" Approx. Length ("B" Engine B- and E-Body)

$ 259.95

CLUTCH LINKAGE SHAFT SERVICE KITS

Complete kits to restore the clutch shaft linkage from the clutch pedal to the clutch fork on rear-wheel-drive manual transmissions. Each kit contains nylon bearings, snap rings, seals, washers, lock springs and pivot ball studs.

Clutch Linkage Shaft Service Kit (B and E-Body)

$ 69.95

Clutch Linkage Shaft Service Kit (A-Body)

$ 69.95

CLUTCH ROD REPAIR KITS

Repair kits for the clutch rod that runs from the clutch linkage to the clutch fork. Each kit contains a clutch rod, nuts, washers, springs, clips and instructions.

Clutch Rod Kit — 6.885" Overall Length (Small Block A-Body)

$ 54.95

Clutch Rod Kit — 4.860" Overall Length (Small Block B and E-Body)

$ 64.95

Clutch Rod Kit — 4.880" Overall Length (Big Block B- and E-Body)

$ 54.95

RACE CLUTCH COVER & PRESSURE PLATE

Race Clutch Cover and Pressure Plate is super heavy-duty for 3100 lbs. spring load.

Race Clutch Cover and Pressure Plate — 10 1/2" (Hemi®, Big Block, Small Block)

DISC

MUSCLE CAR PRESSURE PLATES

These Muscle Car Pressure Plates were designed as replacements for early V8 muscle cars. Both are roller designs similar to original production units. Use with muscle car clutch discs.

Muscle Car Pressure Plate — 10 1/2", 2500 lb. Base (Dodge and Plymouth V8 Muscle Cars)

DISC

Scalloped Muscle Car Pressure Plate -- 11" (10.95"), 2500 lb. Base (1970-72 Hemi and Big Block)

DISC

MUSCLE CAR CLUTCH DISCS

These Muscle Car Clutch Discs are designed as replacements for various Dodge and Plymouth V8 muscle cars.

Muscle Car Clutch Disc — 10 1/2", 23 Spline (Dodge and Plymouth V8 Muscle Cars)

DISC

Muscle Car Clutch Disc — 11" (10.95"), 23 Spline (Dodge and Plymouth V8 Muscle Cars)

$ 149.95 In Stock

Muscle Car Clutch Disc — 10 1/2", 18 Spline (Dodge and Plymouth V8 Muscle Cars)

$ 229.95 In Stock

Muscle Car Clutch Disc — 11" (10.95"), 18 Spline (Dodge and Plymouth V8 Muscle Cars)

DISC

STREET/STRIP PRESSURE PLATES

Pressure Plate — 11" (10.95") (426 Hemi, 440 Big Block)

DISC

Pressure Plate — 10 1/2" (426 Hemi, 440 Big Block, 340 Small Block)

 DISC

PILOT BEARING

Pilot Bearing should be replaced when servicing clutch and throw out bearing. It should be installed with every new clutch.

Pilot Bearing (Big Block and Small Block)

$ 9.95

RWD CLUTCH RELEASE ROLLER BEARING & SLEEVE ASSEMBLY

This Roller Bearing and Sleeve Assembly applies to 4-speed transmissions with 10.50" clutch. Fits only 18-spline input shaft. It should be installed every time you replace your clutch.

RWD Clutch Release Roller Bearing and Sleeve Assembly

$ 129.95

4 SPEED GASKET KIT

Complete Rebuild 4-Speed Gasket Kit for A-833 manual transmissions. Kit includes input seal, large rubber cone-style rear seal and all necessary gaskets and seals.

4-Speed Gasket Kit (A-833) Avalable For Either 18 & 23 Spline Input Shafts

DISC
Click here for alternative part #

4 SPEED FRONT BEARING RETAINERS

Packages include the retainer, retainer gasket and input shaft seal. Bearing retainers are identified by their outside diameter (OD), attaching bolt circle diameter (BC), and corresponding transmission input shaft.

4-Speed Front Bearing Retainer — 4.35" O.D., 3.70" BC, for 23 Spline Input Shaft (A-833)

$ 149.95

4-Speed Front Bearing Retainer — 4.80" O.D., 3.70" BC, for 23 Spline Input Shaft (A-833)

$ 149.95

4-Speed Front Bearing Retainer — 4.80" O.D., 4.16" BC, for 23 Spline Input Shaft (A-833)

$ 149.95

4-Speed Front Bearing Retainer — 4.80" O.D., 4.16" BC, for 18 Spline Input Shaft (A-833)

$ 299.95

RWD OFFSET CLUTCH HOUSING DOWEL PACKAGE

This dowel package contains dowels offset by 0.007", 0.014" and 0.021" (2 each).

RWD Offset Clutch Housing Dowel Package 

$ 68.95

Hi-Performance, Heavy Duty
PRESSURE PLATE, CLUTCH DISC AND THROW OUT BEARING COMPLETE CLUTCH SETUPS!!!

(When ordering, count teeth on flywheel to be sure; does not include the flywheel or the bellhousing)

10-1/2" for 130 tooth Flywheel w/ Aluminum Bellhousing (23 spline)

$ 279.95

11" for 143 tooth Flywheel w/ Cast Iron Bellhousing (23 spline)

$ 299.95

10-1/2" for 130 tooth Flywheel w/ Aluminum Bellhousing (18 spline)

$ 499.95

11" for 143 tooth Flywheel w/ Cast Iron Bellhousing (18 spline)

$ 499.95